產品描述

樂泰® 401™（非仿品）

重量: 20g

特徵：技術氰基丙烯酸酯 化學類型 氰基丙烯酸乙酯

外觀（未固化） 透明 有色液體LMS

初固約15秒, 完全固化24小時

低白化, 沾上傘繩或藝品類後不要在去碰觸液體,如果一直去碰觸白化情形會很明顯.

關鍵基材金屬、塑料和彈性體 本技術數據表適用於 LOCTITE®

使用時可配帶: 謢目鏡 乳膠手套 或 手術手套

🈲用: 棉質類手套,以免高溫仢傷

📌PS: 萬一雙手不小心粘住,請用筆身慢慢推開(剝離效應原理) ‼️

萬一不小心噴到眼鏡,先用清水沖洗後, 盡速就醫

⚠️🆒🔜🔖開封使用結束後,請直立式放入冷藏冰箱存放,延長有效時間壽命.

401™ 生產日期“製造日期參考”刷QR碼。

401™ 設計用於組裝需要均勻應力分佈和強大的張力和/或剪切強度。

供快速粘合各種材料，包括金屬，塑料和彈性體。粘接多孔材料，如木材、紙張、皮革和織物。

NSF國際

註冊到 NSF 類別 P1 用作密封劑，其中食物內部和周圍不可能有食物接觸

加工領域。請聯繫您當地的技術服務中心了解更多 信息和澄清。

未固化材料的典型特性

比重 @ 25 °C 1.1

閃點 - 見 SDS粘度，錐板和板，mPa•s (cP)：

溫度：25 °C，剪切速率：3,000 秒-1

70 到 110LMS粘度 - LVF，25°C，mPa•s (cP)：

主軸 1，轉速 30 rpm 100 至 120

典型固化性能

在正常條件下，大氣水分啟動固化過程。雖然開發了完整的功能強度

在較短的時間內，固化至少持續 24 小時在開發出完全的耐化學性/溶劑性之前。

固化速度與基材 固化速率將取決於所使用的基材。

桌子 下面顯示了在不同材料上實現的固定時間 在 22 °C / 50 % 相對濕度下。這被定義為時間 產生 0.1 N/mm² 的剪切強度。

夾具時間，秒：

鋼 <5

鋁 <5

氯丁橡膠 <5

橡膠、丁腈 <5

ABS <5

聚氯乙烯 <5

聚碳酸酯 5 至 10

酚醛 <5

木（輕木）<5

木材（橡木） 15 至 30

木材（松木） 15 至 20

刨花板 <5

織物 10 至 20

皮革 15 至 30

紙 <5

PRODUCT DESCRIPTION

LOCTITE® 401™ provides the following product characteristics: Technology Cyanoacrylate Chemical Type Ethyl cyanoacrylate Appearance (uncured) Transparent, colorless to straw colored liquidLMS Components One part - requires no mixing Viscosity Low Cure Humidity Application Bonding Key Substrates Metals , Plastics and Elastomers This Technical Data Sheet is valid for LOCTITE® 401™ manufactured from the dates outlined in the "Manufacturing Date Reference" section. LOCTITE® 401™ is designed for the assembly of difficultto-bond materials which require uniform stress distribution and strong tension and/or shear strength. The product provides rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE® 401™ is also suited for bonding porous materials such as wood, paper, leather and fabric. NSF International Registered to NSF Category P1 for use as a sealant where there is no possibilty of food contact in and around food processing areas. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.1 Flash Point - See SDS Viscosity, Cone & Plate, mPa•s (cP): Temperature: 25 °C, Shear Rate: 3,000 s -1 70 to 110LMS Viscosity, Brookfield - LVF,25°C,mPa•s (cP): Spindle 1, speed 30 rpm 100 to 120 TYPICAL CURING PERFORMANCE Under normal conditions, the atmospheric moisture initiates the curing process. Although full functional strength is developed in a relatively short time, curing continues for at least 24 hours before full chemical/solvent resistance is developed. Cure Speed vs. Substrate The rate of cure will depend on the substrate used. The table below shows the fixture time achieved on different materials at 22 °C / 50 % relative humidity. This is defined as the time to develop a shear strength of 0.1 N/mm². Fixture Time, seconds: Steel <5 Aluminum <5 Neoprene <5 Rubber, nitrile <5 ABS <5 PVC <5 Polycarbonate 5 to 10 Phenolic <5 Wood (balsa) <5